Nissan Juke Service and Repair Manual : Condenser

Exploded View

1. Condenser


1. Condenser
2. Refrigerant pressure sensor 3. O-ring
4. Grommet
5. Braket
6. O-ring
7. Liquid tank braket
8. Liquid tank

: N·m (kg-m, in-lb): Do not reuse
: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
Condenser : Removal and Installation: N·m (kg-m, ft-lb)


Condenser : Removal and Installation

CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to HA- 23, "Perform Lubricant Return Operation".

REMOVAL

1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to HA-21, "Recycle Refrigerant".

2. Remove radiator core support upper. Refer to DLK-147, "HR16DE : Removal and Installation".

3. Remove mounting bolt (A), and then disconnect high-pressure flexible hose from condenser.

CAUTION:
Cap or wrap the joint of the A/C piping and condenser with suitable material such as vinyl tape to avoid the entry of air.

Remove mounting bolt (A), and then disconnect high-pressure


Remove mounting bolt (A), and then disconnect high-pressure pipe from condenser.

CAUTION:
Cap or wrap the joint of the A/C piping and condenser with suitable material such as vinyl tape to avoid the entry of air.

5. Remove condenser from vehicle.


5. Remove condenser from vehicle.

CAUTION:
Be careful not to damage core surface of condenser.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.

• Perform lubricant adjusting procedure before installing new condenser. Refer to HA-24, "Lubricant Adjusting Procedure for Compressor Replacement".

• Check for leakages when recharging refrigerant. Refer to HA-19, "Leak Test".

Liquid tank : Removal and Installation

CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to HA- 23, "Perform Lubricant Return Operation".

REMOVAL

1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to HA-21, "Recycle Refrigerant".

2. Disconnect battery cable from negative terminal. Refer to PG-125, "Removal and Installation".

3. Disconnect harness connectors (1) from battery terminal with fusible link.

4. Remove harness fixing clips (A) from F/L · fuse holder bracket.

5. Remove harness fixing clips (A) from F/L · fuseholder bracket.


5. Remove harness fixing clips (A) from F/L · fuseholder bracket.

6. Disconnect harness connector (1) from ECM.

7. Disengage fixing pawls using a remover tool (A), and then


7. Disengage fixing pawls using a remover tool (A), and then remove F/L · fuse holder.

: Vehicle front


8. Move F/L · fuse holder and harness to a location where they do not inhibit


8. Move F/L · fuse holder and harness to a location where they do not inhibit work.

9. Remove harness fixing clip (A) from F/L · fuse holder bracket.

10. Remove mounting bolt (A) and nut (B) of F/L · fuse holder


10. Remove mounting bolt (A) and nut (B) of F/L · fuse holder bracket (1), and then remove F/L · fuse holder bracket.

: Vehicle front


11. Clean liquid tank and its surrounding area, and then remove dust and rust


11. Clean liquid tank and its surrounding area, and then remove dust and rust from liquid tank.

12. Remove mounting bolts, and then remove liquid tank from the condenser.

CAUTION:
Cap or wrap the joint of the A/C piping and liquid tank with suitable material such as vinyl tape to avoid the entry of air.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Replace O-rings of the A/C piping with new ones. Then apply compressor oil to them when installing.

• Perform lubricant adjusting procedure before installing new liquid tank. Refer to HA-24, "Lubricant Adjusting Procedure for Compressor Replacement".

• Check for leakages when recharging refrigerant. Refer to HA-19, "Leak Test".

Refrigerant pressure sensor : Removal and Installation

CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to HA- 23, "Perform Lubricant Return Operation".

REMOVAL

1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to HA-21, "Recycle Refrigerant".

2. Clean refrigerant pressure sensor and its surrounding area, and then remove dust and rust from refrigerant pressure sensor.

3. Disconnect refrigerant pressure sensor connector.

4. Use a adjustable wrench or other tool to hold the refrigerant pressure sensor mounting block, and then remove the refrigerant pressure sensor from the condenser.

CAUTION:
• Be careful not to damage core surface of condenser.

• Cap or wrap the joint of the condenser and liquid tank with suitable material such as vinyl tape to avoid the entry of air.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.

• Check for leakages when recharging refrigerant. Refer to HA-19, "Leak Test".

    Cooler pipe and hose
    Exploded View 1. A/C unit assembly 2. O-ring 3. High-pressure pipe 4. Condenser 5. Low-pressure flexible hose 6. O-ring 7. Compressor 8. O-ring 9. High-pressure flexible hose : Do no ...

    A/C unit assembly
    Exploded View (Automatic Air Conditioning) REMOVAL LHD model 1. A/C unit assembly 2. Drain hose 3. Steering member 4. Instrument stay : Clip : N·m (kg-m, ft-lb) DISASSEMBLY LHD models ...

    Other materials:

    Shift lock system
    Component Function Check 1.CHECK SHIFT LOCK OPERATION (PART 1) 1. Turn ignition switch ON. 2. Shift the selector lever to “P” position. 3. Attempt to shift the selector lever to any other than position with the brake pedal released. Can the selector lever be shifted to any other position? ...

    Component parts
    INTERIOR LIGHTING SYSTEM INTERIOR LIGHTING SYSTEM : Component Parts Location 1. IPDM E/R Refer to PCS-5, "Component Parts Location" 2. BCM Refer to BCS-6, "BODY CONTROL SYSTEM : Component Parts Location" 3. Door lock and unlock switch 4. Front door request switch (driv ...

    ASCD brake switch
    Component Function Check 1.CHECK ASCD BRAKE SWITCH FUNCTION With CONSULT-III 1. Turn ignition switch ON. 2. Select “ENGINE” using CONSULT-III. 3. Select “BRAKE SW1” in “DATA MONITOR” mode. 4. Check “BRAKE SW1” indication under the following conditions. Without CONSULT-III 1. Turn ignition ...