Nissan Juke Service and Repair Manual : Compressor dose dot operate
Description
SYMPTOM Compressor dose not operate.
Diagnosis Procedure
NOTE
:
• Perform self-diagnosis with CONSULT-III before performing symptom diagnosis.
If any malfunction result or
DTC is detected, perform the corresponding diagnosis.
• Check that refrigerant is enclosed in cooler cycle normally. If the refrigerant amount is shortage from proper amount, perform the inspection of refrigerant leakage 1.CHECK A/C INDICATOR
1. Turn ignition switch ON.
2. Operate blower motor.
3. Check that A/C indicator is turned ON/OFF when operating A/C switch.
Is the inspection result normal? YES >> GO TO 2.
NO >> GO TO 5.
2.CHECK MAGNET CLUTCH OPERATION
Check magnet clutch. Refer to HAC-232, "Component Function Check".
Does it operate normally? YES >> GO TO 3.
NO >> Repair or replace malfunctioning parts.
3.CHECK REFRIGERANT PRESSURE SENSOR
Check refrigerant pressure sensor. Refer to EC-423, "Component Function Check".
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace malfunctioning parts.
4.CHECK BCM OUTPUT SIGNAL
With CONSULT-III
1. Select “DATA MONITOR” mode of “ECM” using CONSULT-III.
2. Select “AIR COND SIG” and “HEATER FAN SW”, and check status under the following conditions.
Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation" (with Intelligent Key) or PCS-63, "Removal and Installation" (without Intelligent Key).
NO >> Replace BCM. Refer to BCS-93, "Removal and Installation" (with Intelligent Key) or BCS-161, "Removal and Installation" (without Intelligent Key).
5.CHECK A/C SWITCH
Check A/C switch. Refer to HAC-220, "Component Function Check".
Is the inspection result normal? YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.CHECK BLOWER FAN ON SIGNAL
Check blower fan ON signal. Refer to HAC-222, "Component Function Check".
Is the inspection result normal? YES >> GO TO 7.
NO >> Repair or replace the malfunctioning parts 7.CHECK THERMO CONTROL AMP.
Check thermo control amp. Refer to HAC-224, "Component Function Check".
Is the inspection result normal? YES >> Replace BCM. Refer to BCS-93, "Removal and Installation" (with Intelligent Key) or BCS-161, "Removal and Installation" (without Intelligent Key).
NO >> Repair or replace the malfunctioning parts
Insufficient heating
Description Symptom • Insufficient heating • No warm air comes out. (Air flow volume is normal.) Diagnosis Procedure NOTE: Perform self-diagnosis with CONSULT-III before performing symptom diagn ...Other materials:
Refilling
1. Remove filler plug (1) and gasket from transaxle case.
2. Fill with new gear oil until oil level reaches the specified limit at
filler plug mounting hole as shown in the figure.
Oil grade and
viscosity
: Refer to MA-13, "Fluids and Lubricants".
Oil capacity : Refer to TM-63, " ...
Precautions on seat belt usage
If you are wearing your seat belt properly adjusted, and you are sitting upright
and well back in your seat with both feet on the floor, your chances of being injured
or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN
strongly encourages you and all of your p ...
Cruise control operations
1. ACCEL/RES switch
2. COAST/SET switch
3. CANCEL switch
4. MAIN (ON·OFF) switch
The cruise control allows driving at a speed between 25 to 89 MPH (40 to 144
km/h) without keeping your foot on the accelerator pedal.
To turn on the cruise control, push the MAIN switch on. The CRUISE indicato ...