Nissan Juke Service and Repair Manual : Clutch piping

Exploded View

RS5F92R

1. CSC (Concentric Slave Cylinder)


1. CSC (Concentric Slave Cylinder) 2. Clutch tube
3. Clutch damper
4. Bracket
5. Master cylinder

RS6F94R

1. CSC (Concentric Slave Cylinder)


1. CSC (Concentric Slave Cylinder) 2. Clutch tube
3. Clutch damper
4. Bracket
5. Master cylinder

Hydraulic Layout

1. Clutch tube


1. Clutch tube
2. Lock pin
3. CSC (Concentric Slave Cylinder) 4. Clutch damper
5. Master cylinder
6. Clutch pedal

Removal and Installation

CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately and wash the affected area with water.

REMOVAL

Note the following, and refer to CL-24, "Exploded View" for removal procedure.

• Drain clutch fluid. Refer to CL-10, "RS5F92R : Draining" (RS5F92R) or CL-13, "RS6F94R : Draining" (RS6F94R).

• Press the lock pin into the bleeding connector of the CSC, and then remove clutch tube from CSC.

• Pull the lock pins from the connectors of the clutch damper until the pins stop, and then remove clutch tubes from clutch damper.

• Pull the lock pin from the connector of the clutch master cylinder until the pin stop, and then remove clutch tube from clutch master cylinder.

INSTALLATION

Note the following, and refer to CL-24, "Exploded View" for installation procedure.

CAUTION:
Never damage clutch tube.

• Insert each clutch tube into the CSC bleeding connector, the clutch damper connector, and the clutch master cylinder connector until it contacts the end of each connector.

• Install each lock pin into the clutch damper connector and the clutch master cylinder connector until it contacts the end of each connector.

Inspection and Adjustment

INSPECTION AFTER REMOVAL

• Check the clutch tube for cracks and damage. If the clutch tube has cracks or damage, replace it with a new one.

• Check the O-ring of the clutch tube for cracks and damage. If the O-ring of the clutch tube has cracks or damage, replace clutch tube with a new one.

• Check the clutch damper for cracks and damage. If the clutch damper has cracks or damage, replace it with a new one.

INSPECTION AFTER INSTALLATION

• Check the fluid leakage and the fluid level. Refer to CL-10, "RS5F92R : Inspection" (RS5F92R) or CL-13, "RS6F94R : Inspection" (RS6F94R).

• Check the clutch pedal height, clutch pedal height at clutch disengagement, and clutch pedal play. Refer to CL-7, "Inspection and Adjustment".

ADJUSTMENT AFTER INSTALLATION

Perform the air bleeding. Refer to CL-12, "RS5F92R : Air Bleeding" (RS5F92R) or CL-15, "RS6F94R : Air Bleeding" (RS6F94R).

    Clutch master cylinder
    LHD : Exploded View 1. Reservoir hose 2. Reservoir tank 3. Master cylinder LHD : Removal and Installation REMOVAL CAUTION: • Keep painted surface on the body or other parts free of clutch f ...

    Other materials:

    CVT fluid
    Replacement CVT fluid : Refer to TM-512, "General Specification". Fluid capacity : Refer to TM-512, "General Specificatio CAUTION: • Use only Genuine NISSAN CVT Fluid NS-2. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not cover ...

    C1105, C1106, C1107, C1108 wheel sensor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2. 2.CHECK DTC DETECTION With CONSULT-I ...

    Operating tips (for automatic air conditioner)
    • When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate. This is not a malfunction. After the coolant temperature warms up, air will flow normally from the foot outlets. • The automatic air conditioner is equipped with se ...