Nissan Juke Service and Repair Manual : Clutch pedal position switch
Component Function Check
1.CHECK CLUTCH PEDAL POSITION SWITCH FUNCTION
With CONSULT-III
1. Turn ignition switch ON.
2. Select “ENGINE” using CONSULT-III.
3. Select “CLUTCH P/P SW” in “DATA MONITOR” mode.
4. Check “CLUTCH P/P SW” indication under the following conditions.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector and ground.
Is the inspection result normal? YES >> INSPECTION END
NO >> Go to EC-771, "Diagnosis Procedure".
Diagnosis Procedure
1.CHECK CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect clutch pedal position switch harness connector.
3. Check the continuity between clutch pedal position switch harness connector and ground.
4. Also check harness for short to power.
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair open circuit or short to power in harness or connectors.
2.CHECK CLUTCH PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect ECM harness connector.
2. Check the continuity between clutch pedal position switch harness connector and ECM harness connector.
3. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK CLUTCH PEDAL POSITION SWITCH
Refer to EC-772, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace clutch pedal position switch.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
>> INSPECTION END
Component Inspection
1.CHECK CLUTCH PEDAL POSITION SWITCH-I
1. Turn ignition switch OFF.
2. Disconnect clutch pedal position switch harness connector.
3. Check the continuity between clutch pedal position switch terminals under the following conditions.
Is the inspection result normal? YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK CLUTCH PEDAL POSITION SWITCH-II
1. Adjust clutch pedal position switch installation. Refer to CL-7, "Inspection and Adjustment".
2. Check the continuity between clutch pedal position switch terminals under the following conditions.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace clutch pedal position switch.
ASCD main switch
Component Function Check 1.CHECK ASCD MAIN SWITCH FUNCTION With CONSULT-III 1. Turn ignition switch ON. 2. Select “ENGINE” using CONSULT-III. 3. Select “MAIN SW” in “DATA MONITOR” mode. 4. Check ...Cooling fan
Component Function Check 1.CHECK COOLING FAN FUNCTION With CONSULT-III 1. Turn ignition switch ON. 2. Perform “COOLING FAN” in “ACTIVE TEST” mode with CONSULT-III. 3. Touch “LOW” and “Hi” on the ...Other materials:
Where to go for service
If maintenance service is required or your vehicle appears to malfunction, have
the systems checked and serviced by a NISSAN dealer.
NISSAN technicians are well-trained specialists and are kept up-to-date with
the latest service information through technical bulletins, service tips, and in-deal ...
Preparation
Special Service Tools
BASIC INSPECTION
STEERING WHEEL
Inspection
NEUTRAL POSITION STEERING WHEEL
1. Make sure that steering gear assembly, steering column assembly and
steering wheel are installed in the
correct position.
2. Perform neutral position inspection after wheel alignment. Refer ...
Changing a flat tire
If you have a flat tire, follow the instructions below.
Stopping the vehicle
1. Safely move the vehicle off the road and away from traffic.
2. Turn on the hazard warning flashers.
3. Park on a level surface and apply the parking brake.
4. Continuously Variable Transmission (CVT) models:
Move t ...