Nissan Juke Service and Repair Manual : C1155 brake fluid level switch

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

1. Turn the ignition switch OFF to ON.With CONSULT-III.


1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ABS”.

Is DTC “C1155” detected? YES >> Proceed to BRC-192, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK BRAKE FLUID LEVEL

1. Turn the ignition switch OFF.

2. Check brake fluid level.

- LHD: Refer to BR-12, "Inspection".

- RHD: Refer to BR-80, "Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Refill brake fluid.

• LHD: Refer to BR-12, "Refilling".

• RHD: Refer to BR-80, "Refilling".

2.PERFORM SELF-DIAGNOSIS (1)

1. Erase Self-diagnosis result for “ABS”.With CONSULT-III.


1. Erase Self-diagnosis result for “ABS”.

2. Turn the ignition switch OFF, and wait 10 seconds or more.

3. Turn the ignition switch ON.

CAUTION:
Never start the engine.

4. Perform self-diagnosis for “ABS”.

Is DTC “C1155” detected? YES >> INSPECTION END

NO >> GO TO 3.

3.CHECK BRAKE FLUID LEVEL SWITCH

Check brake fluids level switch. Refer to BRC-194, "Component Inspection".

Is the inspection result normal?

YES >> GO TO 5.

NO >> Replace reservoir tank. GO TO 4.

• LHD: Refer to BR-44, "Disassembly and Assembly".

• RHD: Refer to BR-109, "Disassembly and Assembly".

4.PERFORM SELF-DIAGNOSIS (2)

1. Erase Self-diagnosis result for “ABS”.With CONSULT-III.


1. Erase Self-diagnosis result for “ABS”.

2. Turn the ignition switch OFF, and wait 10 seconds or more.

3. Turn the ignition switch ON.

CAUTION:
Never start the engine.

4. Perform self-diagnosis for “ABS”.

Is DTC “C1155” detected? YES >> INSPECTION END

NO >> GO TO 5.

5.CHECK CONNECTOR AND TERMINAL

1. Turn the ignition switch OFF.

2. Disconnect brake fluid level switch harness connector.

3. Check brake fluid level switch harness connector for disconnection or looseness.

4. Check brake fluid level switch pin terminals for damage or loose connection with harness connector.

5. Disconnect combination meter harness connector.

6. Check combination meter harness connector for disconnection or looseness.

7. Check combination meter pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts. GO TO 6.

6.PERFORM SELF-DIAGNOSIS (3)

1. Connect brake fluid level switch harness connector.With CONSULT-III.


1. Connect brake fluid level switch harness connector.

2. Connect combination meter harness connector.

3. Erase Self-diagnosis result for “ABS”.

4. Turn the ignition switch OFF, and wait 10 seconds or more.

5. Turn the ignition switch ON.

CAUTION:
Never start the engine.

6. Perform self-diagnosis for “ABS”.

Is DTC “C1155” detected? YES >> INSPECTION END

NO >> GO TO 7.

7.CHECK BRAKE FLUID LEVEL SWITCH HARNESS

1. Turn the ignition switch OFF.

2. Disconnect brake fluid level switch harness connector.

3. Disconnect combination meter harness connector.

4. Check continuity between brake fluid level switch harness connector and combination meter harness connector.

*1: 4WD


*1: 4WD
*2: 2WD

5. Check continuity between brake fluid level switch harness connector and ground.

*1: 4WD


*1: 4WD
*2: 2WD

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace error-detected parts. GO TO 8.

8.CHECK BRAKE FLUID LEVEL SWITCH GROUND

Check continuity between brake fluid level switch harness connector and ground.

*1: 4WD


*1: 4WD
*2: 2WD

Is the inspection result normal? YES >> GO TO 9.

NO >> Repair or replace error-detected parts. GO TO 9.

9.CHECK COMBINATION METER

Check combination meter. Refer to MWI-23, "CONSULT-III Function".

Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-233, "Removal and Installation".

NO >> Repair or replace combination meter. Refer to MWI-69, "Removal and Installation".

Component Inspection

1.CHECK BRAKE FLUID LEVEL SWITCH

1. Turn the ignition switch OFF.

2. Disconnect brake fluid level switch harness connector.

3. Check continuity between terminals of brake fluid level switch.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace reservoir tank.

• LHD: Refer to BR-44, "Disassembly and Assembly".

• RHD: Refer to BR-109, "Disassembly and Assembly".

    C1144 incomplete steering angle sensor adjustment
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    C1164, C1165 CV system
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    Other materials:

    Front wiper motor lo circuit
    Component Function Check 1.CHECK FRONT WIPER LO OPERATION CONSULT-III ACTIVE TEST 1. Select “FRONT WIPER” of IPDM E/R active test item. 2. With operating the test item, check front wiper operation. Lo : Front wiper (LO) operation Off : Stop the front wiper. Is front wiper (LO) operation norma ...

    Door cable
    Exploded View LEFT SIDE 1. Heater unit assembly 2. Intake door lever 3. Intake door link 4. Intake door cable 5. Air mix door cable 6. Air mix door link 7. Air mix door rod 8. Lower air mix door lever 9. Upper air mix door lever 10. Max. cool door A. To A/C control RIGHT SIDE ...

    U1402 engine speed signal
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.PERFORM ECM SELF DIAGNOSIS Using CONSULT-III, check the “self diagnosis result” of “ENGINE” and repair or replace any malfunctioning parts. >> • Refer to EC-108, "DTC Index". (MR16DDT) • Refer to EC-522, "DTC Index ...