Nissan Juke Service and Repair Manual : Brake pedal position switch

Component Function Check

1.CHECK BRAKE PEDAL POSITION SWITCH FUNCTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “BRAKE SW1” in “DATA MONITOR” mode of “ENGINE” using CONSULT-III.

3. Check “BRAKE SW1” indication as per the following conditions.

Without CONSULT-III


1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector terminals as per the following.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to EC-425, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect brake pedal position switch harness connector.

3. Turn ignition switch ON.

4. Check the voltage between brake pedal position switch harness connector and ground.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

Is the inspection result normal? YES >> GO TO 2.

NO >> Perform the trouble diagnosis for power supply circuit.

2.CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between brake pedal position switch harness connector and ECM harness connector.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

4. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK BRAKE PEDAL POSITION SWITCH

Check the brake pedal position switch. Refer to EC-426, "Component Inspection (Brake Pedal Position Switch)" Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace brake pedal position switch. Refer to BR-20, "Exploded View" (LHD) or BR-88, "Exploded View" (RHD)

Component Inspection (Brake Pedal Position Switch)

1.CHECK BRAKE PEDAL POSITION SWITCH-I

1. Turn ignition switch OFF.

2. Disconnect brake pedal position harness connector.

3. Check the continuity between brake pedal position switch terminals as per the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> GO TO 2.

2.CHECK BRAKE PEDAL POSITION SWITCH-II

1. Adjust brake pedal position switch installation. Refer to BR-9, "Inspection and Adjustment" (LHD) or BR- 77, "Inspection and Adjustment" (RHD).

2. Check the continuity between brake pedal position switch terminals as per the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace brake pedal position switch. Refer to BR-20, "Exploded View" (LHD) or BR-88, "Exploded View" (RHD).

    Refrigerant pressure sensor
    Component Function Check 1.CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION 1. Start engine and warm it up to normal operating temperature. 2. Turn A/C switch and blower fan switch ON. 3. Check ...

    Clutch pedal position switch
    Component Function Check 1.CHECK FOR CLUTCH PEDAL POSITION SWITCH FUNCTION 1. Turn ignition switch ON. 2. Check the voltage between ECM harness connector and ground. Is the inspection result nor ...

    Other materials:

    Service data and specifications (SDS
    Compressor Lubricant Refrigerant Engine Idling Speed Refer to EC-449, "Idle Speed". Belt Tension Refer to EM-20, "Checking". ...

    Component parts
    Starting system (with intelligent key) : Component Parts Location 1. IPDM E/R Refer to PCS-5, "Component Parts Location". 2. Transmission range switch (CVT models) Refer to TM-131, "CVT CONTROL SYSTEM : Component Parts Location" (MR16DDT), TM-314, "CVT CONTROL SYS ...

    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
    The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is include ...