Nissan Juke Service and Repair Manual : Blower motor
Exploded View
2WD models
1. A/C unit assembly
2. Fan control amp.*1
3. Blower fan resistor*2
4. Blower motor
5. Blower motor cover
• *1: Automatic air conditioner • *2: Manual air conditioner or Manual heater
4WD models
1. A/C unit assembly
2. Blower fan resistor*1
3. Sub harness*1
4. Power transistor*2
5. Sub harness*2
6. Blower motor
• *1: Manual air conditioner • *2: Automatic air conditioner
Removal and Installation (LHD models)
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative
terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1. Remove glove box assembly. Refer to IP-13, "Removal and Installation".
2. Disconnect blower motor harness connector (1) and front passenger air bag module harness connector (2).
3. Remove fixing screws, and then remove blower motor cover. (2WD models
only)
4. Remove front passenger air bag module. Refer to SR-19, "Removal and
Installation".
5. Press flange holding hook (A), and then turn blower motor (1) clockwise.
6. Pull outside, and then remove blower motor.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old mounting bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunctioningparts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-12, "On Board Diagnosis Function" or SRC-16, "CONSULT-III Function".
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Removal and Installation (RHD models)
REMOVAL
1. Remove instrument lower panel. Refer to IP-13, "Removal and Installation".
2. Remove steering column upper cover and steering column lower cover. Refer to IP-13, "Removal and Installation".
3. Remove mounting nuts and harness connector from steering column assembly. Refer to ST-10, "Removal and Installation".
4. Move steering column assembly aside.
5. Disconnect blower motor connector.
6. Press flange holding hook (A), and then turn blower motor (1) clockwise.
7. Pull outside, and then remove blower motor.
INSTALLATION
Install in the reverse order of removal.
Duct and grille
Exploded View FRONT LHD models 1. A/C unit assembly 2. Side ventilator duct LH 3. Foot duct LH 4. Side defroster nozzle LH 5. Side ventilator grille LH 6. Side defroster grille LH 7. In ...Air conditioner filter
Exploded View LHD models 1. A/C unit assembly 2. Air conditioner filter 3. Filter cover Removal and Installation (LHD models) REMOVAL 1. Remove glove box assembly. Refer to IP-13, "Rem ...Other materials:
Periodic maintenance
REAR WHEEL HUB
Inspection
COMPONENT PART
Check the mounting conditions (looseness, back lash) of each component and
component conditions (wear,
damage) are normal.
WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)
Check the following items, and replace the part it necessary.
• Move wheel hub ...
Cockpit
1. Outside mirror remote control switch
2. Headlight, fog light and turn signal switch
— Headlight
— Turn signal light
— Fog light
3. Steering wheel
— Electric power steering system
— Horn
— Driver’s supplemental air bag
4. Wiper and washer switch
5. Shift lever
— Continuously V ...
Sun visors
TILT OPERATION
Push the lock lever down 1 and adjust the steering wheel up or down 2 to the
desired position.
Pull the lock lever up 3 securely to lock the steering wheel in place.
1. To block out glare from the front, swing down the sun visor1 .
2. To block glare from the side, remove the ...