Nissan Juke Service and Repair Manual : Basic inspection

DIAGNOSIS AND REPAIR WORKFLOW

Work Flow

DETAILED FLOW

1.INTERVIEW FROM THE CUSTOMER

Clarify customer complaints before inspection. First of all, perform an interview utilizing STC-17, "Diagnostic Work Sheet" and reproduce symptoms as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving vehicle with customer, if necessary.

CAUTION:
Customers are not professional. Never guess easily like “maybe the customer means that...,” or “maybe the customer mentions this symptom”.

>> GO TO 2.

2.CHECK SYMPTOM

Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by protection function. Refer to STC-13, "Protection Function".

CAUTION:
When the symptom is caused by normal operation, fully inspect each portion and obtain the understanding of customer that the symptom is not caused by a malfunction.

>> GO TO 3.

3.PERFORM SELF-DIAGNOSIS

Perform self-diagnosis for “EPS”.With CONSULT-III


Perform self-diagnosis for “EPS”.

Is any DTC detected? YES >> Record or print self-diagnosis results. GO TO 4.

NO >> GO TO 6.

1. Erase self-diagnostic results for “EPS”.With CONSULT-III


1. Erase self-diagnostic results for “EPS”.

2. Perform DTC confirmation procedures for the error detected system.

NOTE

:
If some DTCs are detected at the same time, determine the order for performing the diagnosis based on STC- 13, "DTC Inspection Priority Chart".

Is any DTC detected? YES >> GO TO 5.

NO >> Check harness and connectors based on the information obtained by interview. Refer to GI-42, "Intermittent Incident".

5.REPAIR OR REPLACE ERROR-DETECTED PARTS

• Repair or replace error-detected parts.

• Reconnect part or connector after repairing or replacing.

• When DTC is detected, erase self-diagnostic results for “EPS”.

>> GO TO 7.

6.IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS

Estimate error-detected system based on symptom diagnosis and perform inspection.

Can the error-detected system be identified?

NO >> Check harness and connectors based on the information obtained by interview. Refer to GI-42, "Intermittent Incident".

7.FINAL CHECK

1. Check the reference value for EPS control unit.With CONSULT-III


1. Check the reference value for EPS control unit.

2. Recheck the symptom and check that symptom is not reproduced on the same conditions.

Is the symptom reproduced? YES >> GO TO 3.

NO >> INSPECTION END

Diagnostic Work Sheet

Description
• In general, customers have their own criteria for a problem. Therefore, it is important to understand the symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.

• In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.

Interview sheet sample


DTC/circuit diagnosis


    Wiring diagram
    ELECTRONICALLY CONTROLLED POWER STEERING SYSTEM Wiring Diagram For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), ...

    Other materials:

    Ring gear shaft
    Exploded View 1. Pinion lock nut 2. Companion flange 3. Drive pion oil seal 4. Pinon rear bearing 5. Transfer case 6. Gasket 7. Filler plug 8. Collapsible spacer 9. Drive pinion adjust shim 10. Drive pinion 11. Pinion front bearing 12. Ring gear 13. Ring gear shaft 14. Ring ...

    Service Notice or Precautions for Manual Transaxle
    CAUTION: • Never reuse CSC (Concentric Slave Cylinder). Because CSC slides back to the original position every time when removing transaxle assembly. At this timing, dust on the sliding parts may damage a seal of CSC and may cause clutch fluid leakage. Refer to CL-27, "Removal and Inst ...

    Security indicator lamp
    Component Function Check 1.CHECK FUNCTION 1. Perform “THEFT IND” in the “ACTIVE TEST” mode of “BCM” using CONSULT-III. 2. Check security indicator lamp operation. Is the inspection result normal? YES >> INSPECTION END NO >> Go to SEC-227, "Diagnosis Procedure". Diagn ...