Nissan Juke Service and Repair Manual : B26F2 ignition relay

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more.

CVT models
- Selector lever is in the P or N position - Do not depress brake pedal

M/T models
- Do not depress clutch pedal

2. Check “Self-diagnosis result” with CONSULT-III.

Is DTC detected? YES >> Go to PCS-105, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK IPDM E/R SELF-DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Erase the DTC of IPDM E/R.

3. Turn ignition switch OFF.

4. Turn ignition switch ON and check the DTC again.

Is DTC detected? YES >> Repair or replace the malfunctioning part. Refer to PCS-25, "DTC Index".

NO >> GO TO 2.

2.CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL

1. Turn ignition switch OFF.

2. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> GO TO 3.

3.CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 1

1. Turn ignition switch OFF.

2. Disconnect BCM and IPDM E/R connectors.

3. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness.

4.CHECK IGNITION RELAY (IPDM E/R) CONTROL SIGNAL CIRCUIT - 2

1. Connect IPDM E/R connectors.

2. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace BCM. Refer to BCS-93, "Removal and Installation".

NO >> Replace IPDM E/R.

    B26F1 ignition relay
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON under the following conditions, and wait for 2 seconds or more. CVT ...

    B26F6 BCM
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B26F6 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B26F6 is disp ...

    Other materials:

    Door does not lock/unlock with door key cylinder operation
    Diagnosis Procedure 1.CHECK POWER DOOR LOCK OPERATION Check power door lock operation. Does door lock/unlock with door lock and unlock switch? YES >> GO TO 2. NO >> Go to DLK-110, "ALL DOOR : Diagnosis Procedure". 2.CHECK UNLOCK SENSOR Check unlock sensor. Refer ...

    Brake piping
    Front : Exploded View WITHOUT ESP 1. Brake tube 2. ABS actuator and electric unit (control unit) 3. Connector 4. Connector bracket 5. Master cylinder assembly 6. Brake booster 7. Lock plate 8. Brake hose 9. Union bolt 10. Copper washer A. To rear brake tube : N·m (kg-m, ft-lb) ...

    P0011 IVT control
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075. Refer to EC-583, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always turn ...