Nissan Juke Service and Repair Manual : B2632, B2633 air mix door motor PBR
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn ignition switch ON.
2. Select “Self Diagnostic Result” mode of “HVAC” using CONSULT-III.
3. Check DTC.
Is DTC detected? YES >> Refer to HAC-155, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK AIR MIX DOOR MOTOR POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between mode door motor harness connector and ground.
Is the inspection result normal? YES >> GO TO 2.
NO >> GO TO 5.
2.CHECK AIR MIX DOOR MOTOR GROUND CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect air mix door motor and A/C auto amp. connector.
3. Check continuity between air mix door motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK AIR MIX DOOR MOTOR LIN SIGNAL
1. Connect air mix door motor and A/C auto amp. connector.
2. Turn ignition switch ON.
3. Confirm output waveform between air mix door motor harness connector and ground using oscilloscope.
Is the inspection result normal? YES >> GO TO 4.
NO >> GO TO 6.
4.CHECK INSTALLATION OF AIR MIX DOOR MOTOR
Check air mix door motor is properly installed. Refer to HAC-195, "Exploded View".
Is the inspection result normal? YES >> Replace air mix door motor. Refer to HAC-197, "AIR MIX DOOR MOTOR : Removal and Installation".
NO >> Repair or replace malfunctioning part.
5.CHECK AIR MIX DOOR MOTOR POWER SUPPLY CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect air mix door motor and A/C auto amp. connector.
3. Check continuity between air mix door motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal? YES >> Replace A/C auto amp. Refer to HAC-188, "Removal and Installation".
NO >> Repair harness or connector.
6.CHECK AIR MIX DOOR MOTOR LIN SIGNAL CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect air mix door motor and A/C auto amp. connector.
3. Check continuity between air mix door motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal? YES >> Replace A/C auto amp. Refer to HAC-188, "Removal and Installation".
NO >> Repair harness or connector.
B2630, B2631 sunload sensor
DTC Logic DTC DETECTION LOGIC NOTE: • If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC- 141, "DTC Logic". • If DTC is displa ...B2636, B2637, B2638, B2639, B2654, B2655 mode door motor
DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE With CONSULT-III 1. Turn ignition switch ON. 2. Select “Self Diagnostic Result” mode of “HVAC” usi ...Other materials:
Intake sensor
Exploded View
Refer to HA-97, "Exploded View (Automatic Air Conditioning)".
Removal and Installation
REMOVAL
1. Remove evaporator assembly. Refer to HA-115, "EVAPORATOR : Removal and
Installation".
2. Remove intake sensor from evaporator.
INSTALLATION
Note the followin ...
Rear power window switch
Component Function Check
1. CHECK REAR POWER WINDOW SWITCH FUNCTION
Check rear power window motor operation with rear power window switch.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Refer to PWC-24, "Diagnosis Procedure".
Diagnosis Procedure
1.CHECK R ...
P0703 brake switch B
Description
BCM detects ON/OFF state of the stop lamp switch and transmits the data to
the CVT control unit via CAN
communication by converting the data to a signal.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CON ...