Nissan Juke Service and Repair Manual : B2615 blower relay circuit

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions, and wait for 1 second or more.

CVT models
- Selector lever is in the P or N position - Do not depress brake pedal

M/T models
- Do not depress clutch pedal

2. Check “Self-diagnosis result” of BCM with CONSULT-III.

Is DTC detected? YES >> Go to PCS-94, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK BLOWER RELAY POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect blower relay.

3. Check voltage between blower relay harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK BLOWER RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between blower relay harness connector and BCM harness connecto

4. Check continuity between blower relay harness connector and ground.


4. Check continuity between blower relay harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace harness.

3.CHECK BLOWER RELAY GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check continuity between blower relay harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair blower relay ground circuit.

4.CHECK BLOWER RELAY POWER SUPPLY CIRCUIT-2

1. Turn ignition switch ON.

2. Check voltage between blower relay harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Check continuity open or short between blower relay and battery.

5.CHECK BLOWER RELAY

Refer to PCS-95, "Component Inspection".

Is the inspection result normal? YES >> GO TO 6.

NO >> Replace blower relay.

6.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK BLOWER RELAY

1. Turn ignition switch OFF.

2. Remove ignition relay.

3. Check the continuity between ignition relay terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace Ignition relay

B2618 BCM


    B2614 ACC relay circuit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn the power supply position to ACC under the following conditions, and wait for 2 second or ...

    B2618 BCM
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2618 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2618 is disp ...

    Other materials:

    B1137 side air bag module LH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III. Without CONSULT-III 1. Turn ignition switch ON. 2. Check the air bag warning lamp statu ...

    Door mirror system (without intelligent key)
    LHD LHD : Wiring Diagram For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information/Explanation of Option Abbreviation". RHD RHD : Wiring Diagram For connector termina ...

    Service Notice
    • When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent scratches. • Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or damage them. • Apply sealing compound where necessary when ins ...