Nissan Juke Service and Repair Manual : B2612 steering status

DTC Logic

DTC DETECTION LOGIC

NOTE

:
• If DTC B2612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic".

• If DTC B2612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE 1

1. Press push-button ignition switch under the following conditions and wait 1 second or more.

- Selector lever: In the P position - Brake pedal: Not depressed 2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected? YES >> Go to SEC-102, "Diagnosis Procedure".

NO >> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE 2

1. Turn ignition switch ON.

2. Turn ignition switch OFF.

3. Press driver side door switch and wait 1 second or more.

4. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected? YES >> Go to SEC-102, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK IPDM E/R INPUT SIGNAL

1. Turn ignition switch OFF.

2. Check voltage between IPDM E/R harness connector and ground.

NOTE:


NOTE:

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 2.

2.CHECK IPDM E/R INPUT SIGNAL CIRCUIT

1. Disconnect IPDM E/R connector and steering lock unit connector.

2. Check continuity between IPDM E/R harness connector and steering lock unit harness connector.

3. Check continuity between IPDM E/R harness connector and ground.


3. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness.

3.REPLACE STEERING LOCK UNIT

1. Replace steering lock unit.

2. Perform the service procedure for steering lock unit replacement. Refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

>> INSPECTION END

4.CHECK BCM INPUT SIGNAL

1. Turn ignition switch OFF.

2. Check voltage between BCM harness connector and ground.

NOTE:


NOTE:

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 6.

5.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.

For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

>> INSPECTION END

6.CHECK BCM INPUT SIGNAL CIRCUIT

1. Disconnect BCM connector and steering lock unit connector.

2. Check continuity between BCM harness connector and steering lock unit harness connector.

3. Check continuity between BCM harness connector and ground.


3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace harness.

7.REPLACE STEERING LOCK UNIT

1. Replace steering lock unit.

2. Perform the service procedure for steering lock unit replacement. Refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

>> INSPECTION END

    B260F Engine status
    Description BCM receives the engine status signal from ECM via CAN communication. DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B260F is displayed with DTC U1000, first perform the trouble diagnos ...

    B2619 BCM
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Press push-button ignition switch under the following conditions and wait 1 second or more. - ...

    Other materials:

    P0868 transmission fluid pressure
    Description The secondary pressure solenoid valve regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATIO ...

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONS ...

    SRS air bag warning lamp does not turn off
    Diagnosis Procedure 1.CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER Check the deployment of air bag module. Is air bag module deployed? YES >> Replace the malfunctioning parts. NO >> GO TO 2. 2.CHECK AIR BAG FUSE Check 10 A fuse [No.2, located in fuse block (J/B)]. Is ...