Nissan Juke Service and Repair Manual : B2608 starter relay

DTC Logic

DTC DETECTION LOGIC

NOTE

:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic".

• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "DTC Logic".

• If DTC B2608 is displayed with DTC B210D (IPDM E/R), first perform the trouble diagnosis for DTC B210D.

Refer to SEC-146, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine.

- Selector lever: In the P position - Brake pedal: Depressed 2. Wait 1 second after engine started.

3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected? YES >> Go to SEC-93, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC OF IPDM E/R

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.

Is DTC detected? YES >> Perform the trouble diagnosis related to the detected DTC. Refer to PCS-25, "DTC Index".

NO >> GO TO 2.

2.CHECK STARTER RELAY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect BCM connector.

4. Check continuity between IPDM E/R harness connector and BCM harness connector.

5. Check continuity between IPDM E/R harness connector and ground.


5. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair or replace harness.

3.REPLACE IPDM E/R

1. Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".

2. Perform DTC CONFIRMATION PROCEDURE for DTC B2608. Refer to SEC-93, "DTC Logic".

Is DTC B2608 detected again? YES >> INSPECTION END

NO >> GO TO 4.

4.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.

For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

>> INSPECTION END

    B2605 shift position
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2605 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2605 is disp ...

    B2609 steering status
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1 1. Press push-button ignition switch under the following conditions and wait 1 second or more. ...

    Other materials:

    FM-AM-SAT radio with Compact Disc (CD) player (Type B)
    1. XM band select button 2. CD insert slot 3. CD EJECT button 4. TUNE/SCROLL knob and AUDIO control button 5. Radio station preset buttons 6. AUX button 7. ON·OFF button/VOLUME control knob 8. FF (forward)/REW (rewind) or SEEK/CATEGORY button 9. CD button 10. FM·AM band select button No ...

    B2623 inside antenna
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 2. Select “INSIDE ANT DIAGNOSIS” in “WORK SUPPORT” mode. 3. Perform inside key antenna (“INSIDE ANT DIAGNOSIS”) on “WORK SUPPORT” of “INTELL ...

    Diagnosis system (IPDM E/R)
    Diagnosis Description AUTO ACTIVE TEST Description In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation. • Oil pressure warning lamp (only for K9K engine models) • Rear window defogger • Front wiper motor • Parking lamp • License p ...