Nissan Juke Service and Repair Manual : B2601 shift position

DTC Logic

DTC DETECTION LOGIC

NOTE

:
• If DTC B2601 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic".

• If DTC B2601 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Shift the selector lever to the P position.

2. Turn ignition switch ON and wait 2 seconds or more.

3. Shift the selector lever to any position other than P, and wait 2 seconds or more.

4. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected? YES >> Go to SEC-79, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK CVT SHIFT SELECTOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect CVT shift selector (detention switch) connector.

3. Check voltage between CVT shift selector (detention switch) harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 2.

2.CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between CVT shift selector (detention switch) harness connector and BCM harness connector.

3. Check continuity between CVT shift selector (detention switch) harness


3. Check continuity between CVT shift selector (detention switch) harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness.

3.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.

For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

>> INSPECTION END

4.CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)

1. Disconnect IPDM E/R connector.

2. Check continuity between CVT shift selector (detention switch) harness connector and IPDM E/R harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace harness.

5.CHECK CVT SHIFT SELECTOR CIRCUIT (BCM)

1. Disconnect BCM connector.

2. Check continuity between CVT shift selector (detention switch) harness connector and BCM harness connector.

3. Check continuity between CVT shift selector (detention switch) harness


3. Check continuity between CVT shift selector (detention switch) harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace harness.

6.REPLACE BCM

1. Replace BCM. Refer to BCS-93, "Removal and Installation".

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.

For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B2601. Refer to SEC-79, "DTC Logic".

Is DTC B2601 detected again? YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".

NO >> INSPECTION END

    B2557 vehicle speed
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2557 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2557 is disp ...

    B2602 shift position
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2602 is disp ...

    Other materials:

    B1150 curtain air bag module LH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III. Without CONSULT-III 1. Turn ignition switch ON. 2. Check the air bag warning lamp statu ...

    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
    The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is include ...

    System
    System Diagram System Description DESCRIPTION • Manual air conditioning system is controlled by each function of thermo control amp., BCM, ECM and IPDM E/R. • Fan speed of blower motor is changed by the combination of fan control dial operation and blower fan resistor control. CONTROL ...