Nissan Juke Service and Repair Manual : B2581, B2582 intake sensor

DTC Logic

DTC DETECTION LOGIC

NOTE

:
• If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC- 141, "DTC Logic".

• If DTC is displayed along with DTC U1010, first perform the trouble diagnosis for DTC U1010. HAC-142, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “Self Diagnostic Result” mode of “HVAC” using CONSULT-III.

3. Check DTC.

Is DTC detected? YES >> Refer to HAC-149, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Proced

1.CHECK INTAKE SENSOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect intake sensor connector.

3. Turn ignition switch ON.

4. Check voltage between intake sensor harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 4.

2.CHECK INTAKE SENSOR GROUND CIRCUIT FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect A/C auto amp. connector.

3. Check continuity between intake sensor harness connector and A/C auto amp harness connector

Is the inspection result normal?


Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair harness or connector.

3.CHECK INTAKE SENSOR

Check intake sensor. Refer to HAC-147, "Component Inspection".

Is the inspection result normal? YES >> Replace A/C auto amp. Refer to HAC-188, "Removal and Installation".

NO >> Replace intake sensor. Refer to HAC-192, "Removal and Installation".

4.CHECK INTAKE SENSOR POWER SUPPLY CIRCUIT FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect A/C auto amp. connector.

3. Check continuity between intake sensor harness connector and A/C auto amp. harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Repair harness or connector.

5.CHECK INTAKE SENSOR POWER SUPPLY CIRCUIT FOR SHORT

Check continuity between intake sensor harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace A/C auto amp. Refer to HAC-188, "Removal and Installation".

NO >> Repair harness or connector.

Component Inspection

1.CHECK INTAKE SENSOR

1. Remove intake sensor. Refer to HAC-192, "Removal and Installation".

2. Check resistance between intake sensor terminals. Refer to applicable table for the normal value.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace intake sensor. Refer to HAC-192, "Removal and Installation".

    B257B, B257C ambient sensor
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC- 141, "DTC Logic". • If DTC is displaye ...

    B2630, B2631 sunload sensor
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC- 141, "DTC Logic". • If DTC is displa ...

    Other materials:

    Clutch pedal position switch
    Component Function Check 1.CHECK FOR CLUTCH PEDAL POSITION SWITCH FUNCTION 1. Turn ignition switch ON. 2. Check the voltage between ECM harness connector and ground. Is the inspection result normal? YES >> INSPECTION END. NO >> Proceed to EC-427, "Diagnosis Procedure" ...

    Diagnosis and repair work flow
    Work Flow OVERALL SEQUENCE DETAILED FLOW 1.GET INFORMATION ABOUT SYMPTOM Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2. 2.CHECK DTC 1. Check DTC for “ENGINE” and “BCM” usin ...

    Symptom diagnosis
    Noise, vibration and harshness (NVH) Troubleshooting NVH troubleshooting Chart 1. Locate the area where noise occurs. 2. Confirm the type of noise. 3. Specify the operating condition of engine. 4. Check specified noise source. If necessary, repair or replace these parts. A: Closely rel ...