Nissan Juke Service and Repair Manual : B2578, B2579 In-vehicle sensor

DTC Logic

DTC DETECTION LOGIC

NOTE

:
• If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC- 141, "DTC Logic".

• If DTC is displayed along with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to HAC- 142, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “Self Diagnostic Result” mode of “HVAC” using CONSULT-III.

3. Check DTC.

Is DTC detected? YES >> Refer to HAC-143, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK IN-VEHICLE SENSOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect in-vehicle sensor connector.

3. Turn ignition switch ON.

4. Check voltage between in-vehicle sensor harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 4.

2.CHECK IN-VEHICLE SENSOR GROUND CIRCUIT FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect A/C auto amp. connector.

3. Check continuity between in-vehicle sensor harness connector and A/C auto amp harness connector.

Is the inspection result normal?


Is the inspection result normal?

YES >> GO TO 3.

NO >> Repair harness or connector.

3.CHECK IN-VEHICLE SENSOR

Check in-vehicle sensor. Refer to HAC-147, "Component Inspection".

Is the inspection result normal? YES >> Replace A/C auto amp. Refer to HAC-188, "Removal and Installation".

NO >> Replace in-vehicle sensor. Refer to HAC-190, "Removal and Installation".

4.CHECK IN-VEHICLE SENSOR POWER SUPPLY CIRCUIT FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect A/C auto amp. connector.

3. Check continuity between in-vehicle sensor harness connector and A/C auto amp. harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Repair harness or connector.

5.CHECK IN-VEHICLE SENSOR POWER SUPPLY CIRCUIT FOR SHORT

Check continuity between in-vehicle sensor harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace A/C auto amp. Refer to HAC-188, "Removal and Installation".

NO >> Repair harness or connector.

Component Inspection

1.CHECK IN-VEHICLE SENSOR

1. Remove in-vehicle sensor. Refer to HAC-190, "Removal and Installation".

2. Check resistance between in-vehicle sensor terminals. Refer to applicable table for the normal value.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace in-vehicle sensor. Refer to HAC-190, "Removal and Installation".

    U1010 control unit (can)
    Description Initial diagnosis of A/C auto amp. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM SELF-DIAGNOSIS With CONSULT-III 1. Turn ignition switch ON. 2. Select “Self ...

    B257B, B257C ambient sensor
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC- 141, "DTC Logic". • If DTC is displaye ...

    Other materials:

    Refilling
    1. Remove filler plug (1). Fill with new gear oil until oil level reaches the specified level near filler plug mounting hole Oil grade and viscosity : Refer to MA-13, "Fluids and Lubricants". Oil capacity : Refer to DLN-167, "General Specification". 2. After refilling oil, ...

    B2622 inside antenna
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 2. Select “INSIDE ANT DIAGNOSIS” in “WORK SUPPORT” mode. 3. Perform inside key antenna (“INSIDE ANT DIAGNOSIS”) on “WORK SUPPORT” of “INTELL ...

    Precaution for Seat Belt Service
    CAUTION: • Before removing the front seat belt pre-tensioner assembly, turn the ignition switch off, disconnect battery negative terminal and wait at least 3 minutes. • Do not use electrical test equipment for front seat belt pre-tensioner connector. • After replacing or reinstalling front s ...