Nissan Juke Service and Repair Manual : B2110 shift position/clutch interlock switch

DTC Logic

DTC DETECTION LOGIC

NOTE

:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 30, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Shift selector lever to the P position.

2. Turn ignition switch ON and wait 1 second or more.

3. Shift selector lever to the N position and wait 1 second or more.

4. Shift selector lever to any position other than P and N, and wait 1 second or more.

5. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.

Is DTC detected? YES >> Go to SEC-153, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC OF BCM

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected? YES >> Perform the trouble diagnosis related to the detected DTC. Refer to BCS-67, "DTC Index".

NO >> GO TO 2.

2.CHECK DTC OF TCM

Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT-III.

Is DTC detected? YES >> Perform the trouble diagnosis related to the detected DTC. Refer to TM-171, "DTC Index" (CVT: RE0F10B) or TM-366, "DTC Index" (CVT: RE0F11A).

NO >> GO TO 3.

3.CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect transmission range swiwtch connector.

4. Check continuity between IPDM E/R harness connector and transmission range swiwtch harness connector

5. Check continuity between IPDM E/R harness connector and ground.


5. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".

NO >> Repair or replace harness.

    B210F shift position/clutch interlock switch
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 30, "DTC Logic". DTC CONFIRMATION PROC ...

    Hood switch
    Component Function Check 1.CHECK FUNCTION 1. Select “HOOD SW” in “Data Monitor” mode of “IPDM E/R” using CONSULT-III. 2. Check “HOOD SW” indication under the following condition. Is the indicati ...

    Other materials:

    B1146 curtain air bag module RH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III. Without CONSULT-III 1. Turn ignition switch ON. 2. Check the air bag warning lamp statu ...

    B2193 chain of ECM-IMMU
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "D ...

    Exterior rear
    1. Lift gate — Intelligent Key system 2. Rear window wiper and washer — Switch operation — Window washer fluid 3. Rear spoiler 4. High-mounted stop light 5. Antenna — Satellite radio antenna 6. Rear window defroster 7. Fuel-filler door — Operation — Fuel recommendation 8. R ...