Nissan Juke Service and Repair Manual : B210B starter control relay
DTC Logic
DTC DETECTION LOGIC
NOTE
:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis
for DTC U1000. Refer to PCS-
30, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or more.
- Selector lever: In the P position - Brake pedal: Depressed 2. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected? YES >> Go to SEC-213, "Diagnosis Procedure".
NO >> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE 2
1. Stop engine.
2. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to EC-366, "DTC Logic" (MR16DDT) or EC-725, "DTC Logic" (HR16DE).
3. Turn ignition switch ON.
4. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected? YES >> Refer to SEC-213, "Diagnosis Procedure".
NO >> INSPECTION EN
Diagnosis Procedure
1.INSPECTION START
Perform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC? DTC confirmation procedure 1>>GO TO 2.
DTC confirmation procedure 2>>GO TO 5.
2.CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES >> Perform the trouble diagnosis related to the detected DTC. Refer to BCS-67, "DTC Index".
NO >> GO TO 3.
3.CHECK IGNITION SWITCH START SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace harness. Refer to STR-12, "CVT : Wiring Diagram".
4.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
1. Reconnect IPDM E/R harness connector.
2. Turn ignition switch ON.
3. Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
4. Touch “ERASE”.
5. Perform DTC CONFIRMATION PROCEDURE for DTC B210B. Refer to SEC-213, "DTC Logic".
Is DTC detected? YES >> Replace IPDM E/R. Refer to PCS-63, "Removal and Installation".
NO >> INSPECTION END
5.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
1. Turn ignition switch ON.
2. Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
3. Touch “ERASE”.
4. Perform DTC CONFIRMATION PROCEDURE for DTC B210B. Refer to SEC-213, "DTC Logic".
Is DTC detected? YES >> Replace IPDM E/R. Refer to PCS-63, "Removal and Installation".
NO >> INSPECTION END
B20A0 cranking request circuit
DTC Logic DTC DETECTION LOGIC NOTE: If DTC B20A0 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 59, "DTC Logic". DTC CONFIRMATION PROC ...B210C starter control relay
DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS-30, "DTC Logic". • When IPDM E/R power ...Other materials:
Shift lock system
Component Function Check
1.CHECK SHIFT LOCK OPERATION (PART 1)
1. Turn ignition switch ON.
2. Shift the selector lever to “P” position.
3. Attempt to shift the selector lever to any other than position with the brake
pedal released.
Can the selector lever be shifted to any other position?
...
System
Starting system (with intelligent key) : System Diagram
*1: M/T models
*2: CVT models
Starting system (with intelligent key) : System Description
CVT MODELS
• When selector lever is P or N, power is supplied to starter relay and
starter control relay by transmission
range switch. And BCM a ...
Precaution Necessary for Steering Wheel Rotation after Battery Disconne
NOTE:
• Before removing and installing any control units, first turn the ignition
switch to the LOCK position, then disconnect
both battery cables.
• After finishing work, confirm that all control unit connectors are connected
properly, then re-connect both
battery cables.
• Always use CONS ...