Nissan Juke Service and Repair Manual : B20A0 cranking request circuit

DTC Logic

DTC DETECTION LOGIC

NOTE

:
If DTC B20A0 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 30, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to EC-366, "DTC Logic" (MR16DDT) or EC-725, "DTC Logic" (HR16DE).

2. Turn ignition switch ON.

3. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.

Is DTC detected? YES >> Refer to SEC-136, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK CRANKING REQUEST SIGNAL

1. Turn ignition switch ON.

2. Check voltage between IPDM E/R harness connector and ground under the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK CRANKING REQUEST SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect ECM connector.

4. Check continuity between IPDM E/R harness connector and ECM harness connector.

5. Check continuity between BCM harness connector and ground.


5. Check continuity between BCM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness.

3.REPLACE IPDM E/R

1. Replace IPDM E/R. Refer to PCS-34, "Removal and Installation".

2. Perform DTC CONFIRMATION PROCEDURE for DTC B20A0. Refer to SEC-136, "DTC Logic".

Is DTC detected? YES >> GO TO 4.

NO >> INSPECTION END

4.REPLACE ECM

Replace ECM.

Refer to EC-447, "Removal and Installation" (MR16DDT) or EC-805, "Removal and Installation" (HR16DE).

>> INSPECTION END

    B209F cranking request circuit
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC B209F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 30, "DTC Logic". DTC CONFIRMATION PROC ...

    B2108 steering lock relay
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC B2108 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 30, "DTC Logic". DTC CONFIRMATION PROC ...

    Other materials:

    Refrigerant pressure sensor
    Exploded View Refer to HA-39, "Exploded View". (HR16DE) Refer to HA-94, "Exploded View". (MR16DDT) Removal and Installation REMOVAL Remove refrigerant pressure sensor. Refer to HA-42, "REFRIGERANT PRESSURE SENSOR : Removal and Installation". (HR16DE) Refer to ...

    P159A, P159C, P159D G sensor
    For M/T models : DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test. 1. Turn ignition switch OFF and wait at least 10 seconds. 2. T ...

    Cooling fan
    Component Function Check 1.CHECK COOLING FAN FUNCTION With CONSULT-III 1. Turn ignition switch ON. 2. Perform “FAN DUTY CONTROL” in “ACTIVE TEST” mode of “ENGINE” using CONSULT-III. 3. Check that cooling fan speed varies according to the percentage. Without CONSULT-III 1. Activate IPDM E/ ...