Nissan Juke Service and Repair Manual : B1080, B1096 driver air bag module

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to SRC-12, "On Board Diagnosis Function".

NOTE

:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected? YES >> Refer to SRC-63, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) • Never use unspecified tester or other measuring device.

1.CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace harness connector.

2.CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace wiring harness.

3.CHECK SPIRAL CABLE CIRCUIT-I

1. Turn ignition switch OFF.

2. Disconnect driver air bag module harness connector and combination switch (spiral cable) harness connector.

3. Check continuity between combination switch (spiral cable) terminals.

Is the inspection result normal?


Is the inspection result normal?

YES >> GO TO 4.

NO >> Replace combination switch (spiral cable). Refer to SR-16, "Removal and Installation".

4.CHECK SPIRAL CABLE CIRCUIT-II

Check continuity between combination switch (spiral cable) terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Replace combination switch (spiral cable). Refer to SR-16, "Removal and Installation".

5.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to SR-30, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-63, "DTC Logic".

Is DTC detected? YES >> GO TO 6.

NO >> INSPECTION END

6.REPLACE DRIVER AIR BAG MODULE

1. Replace driver air bag module. Refer to SR-13, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-63, "DTC Logic".

Is DTC detected? YES >> GO TO 1.

NO >> INSPECTION END

    B1074, B1075, B1076, B1077, B1078, B1079 diagnosis sensor unit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    B1081 seat belt Pre-tensioner RH
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    Other materials:

    Tightening Torque Table (New Standard Included)
    CAUTION: • The special parts are excluded. • The bolts/nuts in these tables have a strength (discrimination) number/symbol assigned to the head or the like. As to the relation between the strength grade in these tables and the strength (discrimination) number/symbol, refer to “DISCRIMINATION ...

    Insufficient cooling
    Description Symptom • Insufficient cooling • No cool air comes out. (Air flow volume is normal.) Diagnosis Procedure NOTE: Perform self-diagnoses with CONSULT-III before performing symptom diagnosis. If any DTC is detected, perform the corresponding diagnosis. 1.CHECK MAGNET CLUTCH OPERA ...

    Component parts
    Component Parts Location 1. Combination meter 2. Intelligent Key warning buzzer 3. Push-button ignition switch 4. Inside key antenna (instrument center) 5. TCM Refer to TM-133, "CVT CONTROL SYSTEM : TCM" (RE0F10B models) or TM-316, "CVT CONTROL SYSTEM : TCM" (RE0F11 ...