Nissan Juke Service and Repair Manual : ASCD steering switch

Component Function Check

1.CHECK ASCD STEERING SWITCH FUNCTION

1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector terminals under the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Go to EC-1011, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK GROUND CONNECTIONS

1. Turn ignition switch OFF.

2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK ASCD STEERING SWITCH CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect combination switch (spiral cable) harness connector.

3. Disconnect ECM harness connector.

4. Check the continuity between combination switch (spiral cable) harness connector and ECM harness connector.

5. Also check harness for short to ground and short to power.


5. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.DETECT MALFUNCTIONING PART

• Harness connector E105, M77 • Combination switch (spiral cable) • Harness for open or short between ECM and combination switch

>> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Check the continuity between combination switch (spiral cable) harness connector and ECM harness connector.

2. Also check harness for short to ground and short to power.


2. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 5.

5.DETECT MALFUNCTIONING PART

• Harness connector E105, M77 • Combination switch (spiral cable) • Harness for open or short between ECM and combination switch (spiral cable)

>> Repair open circuit or short to ground or short to power in harness or connectors.

6.CHECK ASCD STEERING SWITCH

Refer to EC-1012, "Component Inspection".

Is the inspection result normal? YES >> GO TO 7.

NO >> Replace ASCD steering switch.

7.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident", ???GROUND INSPECTION??? and ???INCIDENT SIMULATION TESTS???.

>> INSPECTION END

Component Inspection

1.CHECK ASCD STEERING SWITCH-I

1. Turn ignition switch OFF.

2. Disconnect combination switch (spiral cable) harness connector.

3. Check the continuity between combination switch (spiral cable) harness connector terminals under the following condition.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> Replace ASCD steering switch.

2.CHECK ASCD STEERING SWITCH-II

Check resistance between combination switch (spiral cable) harness connector terminals under the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace ASCD steering switch.

    ASCD main switch
    Component Function Check 1.CHECK ASCD MAIN SWITCH FUNCTION 1. Turn ignition switch ON. 2. Check the voltage between ECM harness connector terminals under the following conditions. Is the inspe ...

    CAN communication circuit
    Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellen ...

    Other materials:

    Blower motor
    Diagnosis Procedure 1.CHECK SYMPTOM Check symptom (A or B). Which symptom is detected? A >>GO TO 2. B >>GO TO 7. 2.CHECK FUSE 1. Turn ignition switch OFF. 2. Check 15A fuses (Nos. 14 and 16, located in fuse block (J/B)]. NOTE: Refer to PG-22, "Fuse, Connector and T ...

    P0850 PNP switch
    Description For CVT models, transmission range switch is turn ON when the selector lever is P or N. For M/T models, park/neutral position (PNP) range switch is ON when the selector lever is Neutral position. ECM detects the position because the continuity of the line (the ON) exists. DTC ...

    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
    The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is include ...