Nissan Juke Service and Repair Manual : ASCD main switch

Component Function Check

1.CHECK ASCD MAIN SWITCH FUNCTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “ENGINE” using CONSULT-III.

3. Select “MAIN SW” in “DATA MONITOR” mode.

4. Check “MAIN SW” indication under the following condition.

Without CONSULT-III


1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the voltage between ECM harness connector and ground under the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Go to EC-768, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK GROUND CONNECTION

1. Turn ignition switch OFF.

2. Check ground connection E21 and E38. Refer to Ground Inspection in GI-44, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK ASCD MAIN SWITCH POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect combination switch (spiral cable) harness connector.

3. Turn ignition switch ON.

4. Check the voltage between combination switch harness connector and ground.

5. Also check harness for short to ground and short to power.


5. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.DETECT MALFUNCTIONING PART

Check the following.

• 10 A fuse (No. 3)
• Combination switch (spiral cable) • Harness for open and short between combination switch and fuse

>> Repair open circuit, short to ground or short to power in harness or connectors.

4.CHECK ASCD MAIN SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Disconnect ECM harness connector.

2. Check the continuity between ECM harness connector and combination switch harness connector.

3. Also check harness for short to ground and short to power.


3. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 5.

5.DETECT MALFUNCTIONING PART

Check the following.

• Harness connectors E105, M77 • Combination switch (spiral cable) • Harness for open and short between ECM and combination switch

>> Repair open circuit, short to ground or short to power in harness or connectors.

6.CHECK ASCD STEERING SWITCH

Refer to EC-769, "Component Inspection (ASCD STEERING SWITCH)".

Is the inspection result normal? YES >> GO TO 7.

NO >> Replace ASCD steering switch.

7.CHECK INTERMITTENT INCIDENT

1. Refer to GI-42, "Intermittent Incident".

Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> Repair open circuit, short to ground or short to power in harness or connectors.

Component Inspection (ASCD STEERING SWITCH)

1.CHECK ASCD STEERING SWITCH-I

1. Turn ignition switch OFF.

2. Disconnect combination switch (spiral cable) harness connector.

3. Check the continuity between combination switch harness connector terminals under the following condition.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> Replace ASCD steering switch.

2.CHECK ASCD STEERING SWITCH-II

Check resistance between combination switch (spiral cable) harness connector terminals under the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace ASCD steering switch.

    ASCD indicator
    Component Function Check 1.CHECK ASCD INDICATOR FUNCTION Check ASCD indicator under the following conditions. Is the inspection result normal? YES >> INSPECTION END NO >> Go to EC-7 ...

    Clutch pedal position switch
    Component Function Check 1.CHECK CLUTCH PEDAL POSITION SWITCH FUNCTION With CONSULT-III 1. Turn ignition switch ON. 2. Select “ENGINE” using CONSULT-III. 3. Select “CLUTCH P/P SW” in “DATA MONITO ...

    Other materials:

    Wheel alignment
    Inspection DESCRIPTION Measure wheel alignment under unladen conditions. NOTE: “Unladen conditions” means that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions. PRELIMINARY CHECK Check the following: • Tires for improper ai ...

    Basic inspection
    DIAGNOSIS AND REPAIR WORK FLOW Work Flow OVERALL SEQUENCE DETAILED FLOW 1.GET INFORMATION FOR SYMPTOM 1. Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). 2. Check operation condition of the function th ...

    Additional service when removing battery negative terminal
    Description • The audio unit is equipped with the anti-theft system. • The audio unit operates after authenticating a fixed four-digit anti-theft code. • After removing the battery of the audio unit, the authentication of the anti-theft code is required. Work Procedure 1.POWER SWITCH ON 1. ...