Nissan Juke Service and Repair Manual : Additional service when replacing ECM
Description
When replacing ECM, this procedure must be performed.
Work Procedure
1.PRECONDITIONING
• Connect a CONSULT-III • Connect a battery charger • Electric load switch is OFF • Wait for the engine to cool [engine coolant temperature < 60?°C (140?°F) and air temperature < 50?°C (122?°F)].
NOTE
:
While the ECM is being programmed the cooling fan motors are triggered
automatically.
>> GO TO 2.
2.SAVE ECM DATA
Turn ignition switch ON.
Perform ???SAVE DATA FOR CPU REPLC??? in WORK SUPPORT mode with CONSULT-III.
>> GO TO 3.
3.REPLACE ECM
Replace ECM.
>> GO TO 4.
4.WRITE ECM DATA
1. Wait at least 30 seconds to turn ON the ignition switch.
2. Perform ???PRGRM REINITIALIZE??? in WORK SUPPORT mode with CONSULT-III.
3. Perform ???WRT DATA AFTR REPLC CPU??? in WORK SUPPORT mode with CONSULT-III.
4. Perform initialization of NATS system and registration of all NATS ignition key IDs.
Refer to SEC-50, "ECM : Work Procedure" (With intelligent key system), SEC-190, "ECM : Work Procedure" (Without intelligent key system).
5. Turn ignition switch OFF, wait at least 30 seconds and then turn ON.
6. Select ???DATA MONITOR??? mode in ECM with CONSULT-III.
7. Check that the ???CODE PROGRAM??? indication.
Which is displayed on CONSULT-III? YES >> GO TO 6.
NO >> GO TO 5.
5.WRITE ECM DATA
1. Perform initialization of NATS system and registration of all NATS ignition key IDs.
Refer to SEC-50, "ECM : Work Procedure" (With intelligent key system), SEC-190, "ECM : Work Procedure" (Without intelligent key system).
2. Turn ignition switch OFF, wait at least 30 seconds and then turn ON.
3. Select ???DATA MONITOR??? mode in ECM with CONSULT-III.
4. Check that the ???CODE PROGRAM??? indication.
Which is displayed on CONSULT-III? YES >> GO TO 6.
NO >> Repeat above steps.
6.PERFORM VIN REGISTRATION
1. Start engine and warm it up to normal operating temperature.
NOTE
:
The start-up phase may last up to 30 seconds.
2. Turn ignition switch OFF, wait at least 30 seconds and then turn ON.
3. Perform ???VIN REGISTRATION??? in WORK SUPPORT mode with CONSULT-III.
4. Follow the instruction of CONSULT-III display.
NOTE
:
After replace ECM, stored DTC may appear on other control unit. Clear the
malfunction memory of these
control unit.
>> END
Basic inspection
Description NOTE: Only consult the tests after following the diagnostic procedure chart. Some specific checks are grouped under the ???tests??? heading and are used as required in different dia ...EGR volume control valve closed position learning
Description EGR Volume Control Valve Closed Position Learning is an operation to learn the fully closed position of the EGR volume control valve by monitoring the EGR volume control valve control ...Other materials:
Door motor
Exploded View
LEFT SIDE
1. A/C unit assembly
2. Intake door lever
3. Intake door link
4. Intake door motor
5. Air mix door motor
6. Air mix door link
7. Max. cool door
8. Upper air mix door lever
9. Air mix door rod
10. Lower air mix door lever
RIGHT SIDE
1. A/C unit assembly ...
C1105, C1106, C1107, C1108 wheel sensor
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn
ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-I ...
P1564 ASCD steering switch
DTC Logic
DTC DETECTION LOGIC
NOTE:
If DTC P1564 is displayed with DTC P0605, first perform the trouble diagnosis
for DTC P0605. Refer to
EC-683, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn
...