Nissan Juke Service and Repair Manual : P1585 G sensor

Description

• G sensor is installed to floor under instrument lower cover.

• G sensor detects longitudinal G and inclination that affects the vehicle and outputs to ECM using analog voltage.

ECM converts the analog voltage value to digital signal and transmits the signal to TCM via CAN communication.

• TCM detects longitudinal G and inclination of the vehicle using information of CAN communication.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

CAUTION:
Always drive vehicle at a safe speed.

1.PRECONDITIONING

Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.With CONSULT-III


1. Start the engine.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “VEHICLE SPEED”.

4. Using the “D” position, increase vehicle speed in constant acceleration within 5 seconds.

5. Select “Self Diagnostic Results” in “TRANSMISSION”.

Is “P1585” detected? YES >> Go to TM-236, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK G SENSOR SIGNAL

1. Park vehicle on level surface.With CONSULT-III


1. Park vehicle on level surface.

2. Turn ignition switch ON.

3. Select “Data Monitor” in “TRANSMISSION”.

4. Select “G SEN SLOPE”.

5. Check display of “G SEN SLOPE”.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 2.

2.CHECK G SENSOR POWER SOURCE

1. Turn ignition switch OFF.

2. Disconnect G sensor connector.

3. Turn ignition switch ON.

4. Check voltage between G sensor vehicle side harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 7.

3.CHECK HARNESS BETWEEN TCM AND G SENSOR (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connectors.

3. Check continuity between TCM vehicle side harness connector terminals and G sensor vehicle side harness connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK HARNESS BETWEEN TCM AND G SENSOR (PART 2)

Check continuity between TCM vehicle side harness connector terminals and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace damaged parts.

5.CHECK G SENSOR

1. Remove G sensor. Refer to TM-282, "Removal and Installation".

2. Reconnect all the connectors.

3. Turn ignition switch ON.

4. Check voltage between TCM connector terminal and ground.

force: Direction of gravitational
force


Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Replace G sensor. Refer to TM-282, "Removal and Installation".

6.PERFORM CALIBRATION

1. Install G sensor. Refer to TM-282, "Removal and Installation".

2. Select “Self Diagnostic Results” in “TRANSMISSION”.

3. Select “Erase”.

4. Perform “G SENSOR REMOVAL/INSTALLATION AND REPLACEMENT”. Refer to TM-182, "Description".

Is calibration complete normally? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

7.CHECK HARNESS BETWEEN TCM AND G SENSOR (SENSOR POWER CIRCUIT) (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connectors.

3. Check continuity between TCM vehicle side harness connector terminal and G sensor vehicle side harness connector terminal.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace damaged parts.

8.CHECK HARNESS BETWEEN TCM AND G SENSOR (SENSOR POWER CIRCUIT) (PART 2)

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace damaged parts.

Special Repair Requirement

1.PERFORM G SENSOR CALIBRATION

Perform “G SENSOR REMOVAL/INSTALLATION AND REPLACEMENT”.

>> Refer to TM-182, "Description".

    P0868 transmission fluid pressure
    Description The secondary pressure solenoid valve regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM. DTC Logic DTC DETECTION LOGIC DTC C ...

    P1701 TCM
    Description When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diagnosis memory function stops, malfunction is detected. NOTE: Since “P1701” ...

    Other materials:

    System
    Automatic air conditioning system : System Diagram Automatic air conditioning system : System Description DESCRIPTION • Automatic air conditioning system is controlled by each function of A/C auto amp., BCM, ECM and IPDM E/ R. • Each operation of air conditioning system is transmitted from ...

    Excessive consumption
    Description CHART 15:EXCESSIVE CONSUMPTION Diagnosis Procedure 1.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT Check ECM power supply and ground circuit. Refer to EC-885, "Diagnosis Procedure". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or replace ha ...

    B2603 shift position
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2603 is displayed with DTC B2601, first perform the trouble diagnosis for DTC B2601. Refer to SEC-79, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1 1. Shift the selector lever to the P position. 2. T ...