Nissan Juke Service and Repair Manual : P1585 G sensor

Description

• G sensor is installed to floor under instrument lower cover.

• G sensor detects longitudinal G and inclination that affects the vehicle and outputs to ECM using analog voltage.

ECM converts the analog voltage value to digital signal and transmits the signal to TCM via CAN communication.

• TCM detects longitudinal G and inclination of the vehicle using information of CAN communication.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

CAUTION:
Always drive vehicle at a safe speed.

1.PRECONDITIONING

Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.With CONSULT-III


1. Start the engine.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “VEHICLE SPEED”.

4. Using the “D” position, increase vehicle speed in constant acceleration within 5 seconds.

5. Select “Self Diagnostic Results” in “TRANSMISSION”.

Is “P1585” detected? YES >> Go to TM-236, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK G SENSOR SIGNAL

1. Park vehicle on level surface.With CONSULT-III


1. Park vehicle on level surface.

2. Turn ignition switch ON.

3. Select “Data Monitor” in “TRANSMISSION”.

4. Select “G SEN SLOPE”.

5. Check display of “G SEN SLOPE”.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 2.

2.CHECK G SENSOR POWER SOURCE

1. Turn ignition switch OFF.

2. Disconnect G sensor connector.

3. Turn ignition switch ON.

4. Check voltage between G sensor vehicle side harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 7.

3.CHECK HARNESS BETWEEN TCM AND G SENSOR (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connectors.

3. Check continuity between TCM vehicle side harness connector terminals and G sensor vehicle side harness connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK HARNESS BETWEEN TCM AND G SENSOR (PART 2)

Check continuity between TCM vehicle side harness connector terminals and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace damaged parts.

5.CHECK G SENSOR

1. Remove G sensor. Refer to TM-282, "Removal and Installation".

2. Reconnect all the connectors.

3. Turn ignition switch ON.

4. Check voltage between TCM connector terminal and ground.

force: Direction of gravitational
force


Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Replace G sensor. Refer to TM-282, "Removal and Installation".

6.PERFORM CALIBRATION

1. Install G sensor. Refer to TM-282, "Removal and Installation".

2. Select “Self Diagnostic Results” in “TRANSMISSION”.

3. Select “Erase”.

4. Perform “G SENSOR REMOVAL/INSTALLATION AND REPLACEMENT”. Refer to TM-182, "Description".

Is calibration complete normally? YES >> INSPECTION END

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

7.CHECK HARNESS BETWEEN TCM AND G SENSOR (SENSOR POWER CIRCUIT) (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connectors.

3. Check continuity between TCM vehicle side harness connector terminal and G sensor vehicle side harness connector terminal.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace damaged parts.

8.CHECK HARNESS BETWEEN TCM AND G SENSOR (SENSOR POWER CIRCUIT) (PART 2)

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace damaged parts.

Special Repair Requirement

1.PERFORM G SENSOR CALIBRATION

Perform “G SENSOR REMOVAL/INSTALLATION AND REPLACEMENT”.

>> Refer to TM-182, "Description".

    P0868 transmission fluid pressure
    Description The secondary pressure solenoid valve regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM. DTC Logic DTC DETECTION LOGIC DTC C ...

    P1701 TCM
    Description When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diagnosis memory function stops, malfunction is detected. NOTE: Since “P1701” ...

    Other materials:

    P2119 electric throttle control function
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK INTERMITTENT INCIDENT Refer to GI-42, "Intermittent Incident". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or replace. 2.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR 1. Replace electric t ...

    P2138 APP sensor
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-307, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always perform ...

    Child safety
    WARNING Do not allow children to play with the seat belts. Most seating positions are equipped with Automatic Locking Retractor (ALR) mode seat belts. If the seat belt becomes wrapped around a child’s neck with the ALR mode activated, the child can be seriously injured or killed if the seat b ...