Nissan Juke Owners Manual : Windshield wiper and washer switch

WARNING

In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.

CAUTION

Do not operate the washer continuously for more than 30 seconds.

Do not operate the washer if the reservoir tank is empty.

Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

Pre-mix washer fluid concentrates with water to the manufacturers recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water.

If the windshield wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approximately 1 minute, turn the switch on again to operate the wiper.

The windshield wiper and washer operates when the ignition switch is in the ON


The windshield wiper and washer operates when the ignition switch is in the ON position.

Push the lever down to operate the wiper at the following speed:

1 Intermittent intermittent operation can be adjusted by turning the knob toward A (Slower) orB (Faster).

2 Low continuous low speed operation 3 High continuous high speed operation

Push the lever up 4 to have one sweep operation of the wiper.

Pull the lever toward you 5 to operate the washer. Then the wiper will also operate several times.

Pulling up the wiper arm:

The wiper arm should be in the up position when replacing the wiper.

To pull up the wiper arm, push the lever4 up twice when the ignition switch is in the OFF position within 1 minute. The wiper operation stops in mid-operation.

To replace the wiper arm, place the wiper arm in the down position and then push the lever 4 up once.

CAUTION

This function can be operated even if the ignition switch is in the ON position. However, to prevent an accident or damage when pulling up the wiper arm, be sure to observe the following precautions.

Make sure the shift lever is in the P (Park) position (Continuously Variable Transmission models).

Make sure the shift lever is in the N (Neutral) position, with the parking brake fully applied (Manual Transmission models).

Never allow the passengers to operate the windshield wiper switch inadvertently.

Do not operate the windshield wiper while the wiper arm is pulled up. The wiper arm may be damaged.

    NISSAN Vehicle Immobilizer System
    The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key. If the engine fails to start using the registered key, it may be due to interference ...

    Rear window wiper and washer switch
    WARNING In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window. CAUTION ...

    Other materials:

    Door lock operation warning does not operate
    Diagnosis Procedure 1.CHECK DOOR LOCK FUNCTION Check door lock function. Does door lock/unlock using door request switch? YES >> GO TO 2. NO >> Refer to DLK-85, "Component Function Check". 2.CHECK INTELLIGENT KEY WARNING BUZZER Check Intelligent Key warning buzzer. ...

    Parts Requiring Angle Tightening
    Use the angle wrench [SST: KV10112100] for the final tightening of the following engine parts: - Cylinder head bolts - Lower cylinder block bolts - Connecting rod cap bolts - Crankshaft pulley bolt (No the angle wrench is required as bolt flange is provided with notches for angle tighteni ...

    Operation inspection
    Work Procedure The purpose of the operational check is to check that the individual system operates normally. Check condition : Engine running at normal operating temperature. 1.CHECK BLOWER MOTOR 1. Operate fan control dial. 2. Check that fan speed changes. Check operation for all fan speeds ...