Nissan Juke Service and Repair Manual : Insufficient heating

Description

Symptom
• Insufficient heating
• No warm air comes out. (Air flow volume is normal.)

Diagnosis Procedure

NOTE

:
Perform self-diagnoses with CONSULT-III before performing symptom diagnosis. If any DTC is detected, perform the corresponding diagnosis.

1.CHECK COOLING SYSTEM

1. Check engine coolant level and check for leakage. Refer to the following.

- HR16DE: Refer to CO-37, "Inspection".

- MR16DDT: Refer to CO-11, "Inspection".

- K9K: Refer to CO-62, "Inspection".

2. Check radiator cap (HR16DE and MR16DDT) or reservoir tank cap (K9K). Refer to the following.

- HR16DE: Refer to CO-40, "RADIATOR CAP : Inspection".

- MR16DDT: Refer to CO-15, "RADIATOR CAP : Inspection".

- K9K: Refer to CO-65, "Inspection".

3. Check water flow sounds of the engine coolant. Refer to the following.

- HR16DE: Refer to CO-38, "Refilling".

- MR16DDT: Refer to CO-12, "Refilling".

- K9K: Refer to CO-63, "Refilling".

Is the inspection result normal? YES-1 >> HR16DE and MR16DDT: GO TO 3.

YES-2 >> K9K: GO TO 2.

NO >> Refill engine coolant and repair or replace the parts depending on the inspection results.

2.CHECK PTC HEATER OPERATION

Check PTC heater operation. Refer to HAC-294, "Component Function Check".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace parts depending on the inspection results.

3.CHECK HEATER HOSE

Check installation of heater hose by visually or touching.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace parts depending on the inspection results.

4.CHECK HEATER CORE

1. Check temperature of inlet hose and outlet hose of heater core.

2. Check that inlet side of heater core is hot and the outlet side is slightly lower than/almost equal to the inlet side.

CAUTION:
Always perform the temperature inspection in a short period of time because the engine coolant temperature is very hot.

Is the inspection result normal?

YES >> GO TO 5.

NO-1 >> HR16DE: Replace heater core. Refer to HA-56, "HEATER CORE : Removal and Installation".

NO-2 >> MR16DDT: Replace heater core. Refer to HA-116, "HEATER CORE : Removal and Installation".

NO-3 >> K9K: Replace heater core.

5.CHECK AIR LEAKAGE FROM EACH DUCT

Check duct and nozzle, etc. of the air conditioning system for air leakage.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace parts depending on the inspection results.

6.CHECK SETTING OF TEMPERATURE SETTING TRIMMER

1. Check setting value of temperature setting trimmer. Refer to HAC-139, "Temperature Setting Trimmer".

2. Check that temperature setting trimmer is set to “− direction”.

NOTE

:
The control temperature can be set by the temperature setting trimmer.

3. Set difference between the set temperature and control temperature to “0”.

Are the symptoms solved? YES >> INSPECTION END

NO >> Replace A/C auto amp. Refer to HAC-188, "Removal and Installation".

    Insufficient cooling
    Description Symptom • Insufficient cooling • No cool air comes out. (Air flow volume is normal.) Diagnosis Procedure NOTE: Perform self-diagnoses with CONSULT-III before performing symptom diagn ...

    Compressor dose dot operate
    Description SYMPTOM Compressor dose not operate. Diagnosis Procedure NOTE: • Perform self-diagnoses with CONSULT-III before performing symptom diagnosis. If any DTC is detected, perform the co ...

    Other materials:

    Fog light switch (if so equipped)
    To turn the fog lights on, turn the headlight switch to the position, then turn the switch to the position. To turn them off, turn the switch to the OFF position. The headlights must be on for the fog lights to operate. When the headlight switch is in the AUTO position, turning the fog lig ...

    Component parts
    Component Parts Location 1. Front door speaker LH 2. Rear door speaker LH 3. Rear view camera 4. Rear door speaker RH 5. Antenna rod 6. Antenna base (antenna amp.) 7. Front door speaker RH 8. Microphone 9. GPS antenna 10. Tweeter LH 11. Steering switch 12. USB connector and AUX ...

    P0703 brake switch B
    Description BCM detects ON/OFF state of the stop lamp switch and transmits the data to the CVT control unit via CAN communication by converting the data to a signal. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CON ...