Nissan Juke Owners Manual : Indicator lights

light (AWD model) All-Wheel Drive (AWD) indicator
light (AWD model)

When the ignition switch is in the ON position, the All-Wheel Drive (AWD) indicator light illuminates and then turns off.

When selecting AWD mode while the engine is running, the AWD indicator light illuminates.

(See All-Wheel Drive (AWD) .) All-Wheel Drive (AWD-V) indicator light (AWD model)
All-Wheel Drive (AWD-V) indicator light (AWD model)

When selecting AWD-V mode while the engine is running, the AWD-V indicator light illuminates.

(See All-Wheel Drive (AWD) .) Continuously Variable Transmission (CVT) indicator light (if so equipped)
Continuously Variable Transmission (CVT) indicator light (if so equipped)

When the ignition switch is in the ON position, the Continuously Variable Transmission (CVT) indicator light illuminates and then turns off.

Cruise main switch indicator: Cruise indicator light


Cruise main switch indicator:

This light illuminates when the cruise control main switch is pushed. The light turns off when the main switch is pushed again. When the cruise indicator light illuminates, the cruise control system is operational.

Cruise malfunction:

If the cruise indicator light blinks while the engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by a NISSAN dealer.

See Cruise control .

light (if so equipped) Engine start operation indicator
light (if so equipped)

This light appears when the shift lever is in the P (Park) position (Continuously Variable Transmission (CVT) models) or N (Neutral) position (Manual Transmission (MT) models). This light means that the engine will start by pushing the ignition switch with the brake pedal depressed.

You can start the engine directly in any position.

This indicator illuminates when the headlight switch is turned to the AUTO (if Exterior light indicator


This indicator illuminates when the headlight switch is turned to the AUTO (if so equipped), position and the front parking lights, or
instrument panel lights, rear combination lights, license plate lights or headlights position and the front parking lights,
instrument panel lights, rear combination lights, license plate lights or headlights are on. The indicator turns off when these lights are turned off.

light Front passenger air bag status
light

The front passenger air bag status light (located on the center of the instrument panel) will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.

For front passenger air bag status light operation, see NISSAN Advanced Air Bag System (front seats)  of this manual.

This light illuminates when the headlight high beam is on and goes out when the High beam indicator light


This light illuminates when the headlight high beam is on and goes out when the low beam is selected.

If the malfunction indicator light illuminates steady or blinks while the engine Malfunction Indicator Light (MIL)


If the malfunction indicator light illuminates steady or blinks while the engine is running, it may indicate a potential emission control and/or Continuously Variable Transmission (CVT) malfunction.

The malfunction indicator light may also illuminate steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 US gallons (11.4 liters) of fuel in the fuel tank.

After a few driving trips, the light should turn off if no other potential emission control system malfunction
light should turn off if no other potential emission control system malfunction exists.

If this indicator light remains on for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/ maintenance test. (See Readiness for Inspection/ Maintenance (I/M) test .) Operation:

The malfunction indicator light will illuminate in one of two ways:

Malfunction indicator light illuminated steady An emission control system and/or CVT malfunction has been detected. Check the fuel-filler cap if the LOOSE FUEL CAP warning message is displayed on the twin trip odometer. If the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The driving trips. If the  light does not light should turn off after a few
driving trips. If the turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. light does not
turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

Malfunction indicator light blinking An engine misfire has been detected which may damage the emission control system.

To reduce or avoid emission control system damage:

1) Do not drive at speeds above 45 MPH (72 km/h).

2) Avoid hard acceleration or deceleration.

3) Avoid steep uphill grades.

4) If possible, reduce the amount of cargo being hauled or towed.

The malfunction indicator light may stop blinking and remain on.

Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without having the emission control system and/or CVT system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.

The light blinks when the ignition switch is in the ACC, OFF or LOCK position. Security indicator light


The light blinks when the ignition switch is in the ACC, OFF or LOCK position. This function indicates the security system equipped on the vehicle is operational.

If the security system is malfunctioning, this light will remain on while the ignition switch is in the ON position. For additional information, see Security systems .

The light flashes when the turn signal switch lever or hazard switch is turned Turn signal/hazard indicator lights


The light flashes when the turn signal switch lever or hazard switch is turned on.

Vehicle Dynamic Control (VDC) off indicator light Dynamic The light comes on when the Vehicle
Dynamic

Control (VDC) off switch is pushed to OFF. This indicates that the VDC system and traction control system are not operating.

    Warning lights
    All-Wheel Drive (AWD) warning light (AWD model) When the ignition switch is in the ON position, the All-Wheel Drive (AWD) warning light will illuminate. It will turn off soon after the engine ...

    Audible reminders
    Key reminder chime Models with Intelligent Key system: A chime will sound if the driver side door is opened while the ignition switch is pushed to the ACC position. Make sure the ignition switch ...

    Other materials:

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. Always use CONS ...

    Tire chains
    Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturers suggestions. Use only SAE Class ...

    Installing front license plate
    Use the following steps to mount the license plate: Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag.   License plate bracket   J-nut  2   Screw  2 Screw grommet  2 1. Park the vehicle on flat, level g ...