Nissan Juke Service and Repair Manual : B1065, B1070 passenger air bag module

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III.

1. Turn ignition switch ON.Without CONSULT-III


1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to SRC-12, "On Board Diagnosis Function".

NOTE

:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected? YES >> Refer to SRC-54, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) • Never use unspecified tester or other measuring device.

1.CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace harness connector.

2.CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace wiring harness.

3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace air bag diagnosis sensor unit. Refer to SR-30, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-54, "DTC Logic".

Is DTC detected? YES >> GO TO 4.

NO >> INSPECTION END

4.REPLACE PASSENGER AIR BAG MODULE

1. Replace passenger air bag module. Refer to SR-19, "Removal and Installation".

2. Perform DTC confirmation procedure. Refer to SRC-54, "DTC Logic".

Is DTC detected?

YES >> GO TO 1.

NO >> INSPECTION END

    B1058, B1059, B1060, B1061, B1062, B1063 diagnosis sensor unit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    B1066, B1071 passenger air bag module
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSU ...

    Other materials:

    Basic inspection
    DIAGNOSIS AND REPAIR WORKFLOW Work Flow OVERALL SEQUENCE DETAILED FLOW 1.INTERVIEW FOR MALFUNCTION Interview the symptom to the customer. >> GO TO 2. 2.SYMPTOM CHECK Check the symptom from the customer's information. >> GO TO 3. 3.BASIC INSPECTION Check the operation o ...

    P0470 exhaust gas pressure sensor 1
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0470 is displayed with DTC P0651 or P2263, first perform trouble diagnosis for DTC P0651 or P2263. Refer to EC-975, "DTC Logic" (P0651), EC-1003, "DTC Logic" (P2263). Diagnosis Procedure 1.CHECK GROUND CONNECTIONS 1. Turn i ...

    Fuel injector and fuel tube
    Exploded View 1. Stud bolt 2. O-ring (green) 3. Fuel injector (front) 4. Clip 5. Fuel injector (rear) 6. O-ring (black) 7. Fuel tube protector 8. Fuel tube 9. Fuel feed hose 10. Quick connector cap A. To centralized under-floor piping : Always replace after every disassembly. ...